Build Your Own Clone Message Board
It is currently Sun Apr 28, 2024 9:06 am

View unanswered posts | View active topics


Board index » Build Your Own Clone » Effects Pedal Technical Support » Compressors

All times are UTC - 6 hours




Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Previous topic | Next topic 
Author Message
Garster123
PostPosted: Mon Apr 10, 2023 11:46 pm 
Offline

Joined: Fri Nov 20, 2020 1:15 pm
Posts: 26
I have found the v2.0 instructions are not compatible with the v2.2 circuit board. When I got to the socket installation, "Step 3: Add the 4 x 2 pin header socket", I couldn't find one included, then noticed the board didn't have a spot for one as indicated in the instructions. Can I get a copy of the v2.2 instructions, I couldn't find it on your website.
Thanks,
Gar
Top
 Profile  
 
duhvoodooman
PostPosted: Tue Apr 11, 2023 9:06 am 
Offline
Moderator
User avatar

Joined: Tue Jan 02, 2007 1:24 pm
Posts: 16224
Location: Albany, NY
The 2.0 instructions are all I could find, as well. If you could post a good photo of the 2.2 PCB, I'm quite sure that we can provide alternative instructions to get you through the differences. In the meantime, I'll let Keith know about the lack of up-to-date instructions on the current kit.

_________________
“My favorite programming language is SOLDER” - Bob Pease (RIP)

My Website * My Musical Gear * My DIY Pedals: Pg.1 - Pg.2
Top
 Profile  
 
Garster123
PostPosted: Tue Apr 11, 2023 10:03 am 
Offline

Joined: Fri Nov 20, 2020 1:15 pm
Posts: 26
Thanks DVM, I've uploaded the picture of the v2.2 board. As you can see, the holes for the 4x2 pin header socket are not there, but the instructions show them. I am stuck until I know how to proceed.
Thanks for your help,
G
Attachment:
File comment: v2.2 - 5 knob compressor circuit board
IMG_5014.jpg
IMG_5014.jpg [ 754.14 KiB | Viewed 1186 times ]
ar
Top
 Profile  
 
byoc
PostPosted: Tue Apr 11, 2023 11:25 am 
Offline
Site Admin
User avatar

Joined: Sun Jan 22, 2006 1:39 pm
Posts: 5991
Location: Richland, WA
The link keeps redirecting. Actually, the old file keeps replacing the new file.

I'll fix it. Again. If the old file hasn't been replace, you can use one of the footswitch wiring diagrams from any of the other intructions.

_________________
*patience is a virtue*

Please do not PM me. email is prefered. keith@buildyourownclone.com
Top
 Profile  
 
duhvoodooman
PostPosted: Tue Apr 11, 2023 11:38 am 
Offline
Moderator
User avatar

Joined: Tue Jan 02, 2007 1:24 pm
Posts: 16224
Location: Albany, NY
Ah, OK, that's exactly what I expected to see. BYOC stopped using the footswitch mini-PCB with the header & socket connectors a while back--they turned out to cause more problems than they solved. So you just need to run wires from those numbered eyelets above the footswitch cutout to the corresponding lugs on the footswitch. Follow the diagram on pg. 23 of the Classic Overdrive instructions, which is set up the exact same way: http://byocelectronics.com/classicodinstructions.pdf

The wiring on mine is pictured below:

Attachment:
COD_footswitch_wiring.jpg
COD_footswitch_wiring.jpg [ 83.95 KiB | Viewed 1181 times ]

_________________
“My favorite programming language is SOLDER” - Bob Pease (RIP)

My Website * My Musical Gear * My DIY Pedals: Pg.1 - Pg.2
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » Build Your Own Clone » Effects Pedal Technical Support » Compressors

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group