Build Your Own Clone Message Board

It is currently Fri Dec 06, 2024 8:21 am

All times are UTC - 6 hours




Post new topic Reply to topic  [ 10 posts ] 
Author Message
PostPosted: Mon Oct 21, 2024 4:19 am 
Offline
User avatar

Joined: Fri Oct 11, 2024 1:32 pm
Posts: 22
I want to add sockets to the IC-chip(s) to make swapping them easier. But I am concerned about the vertical clearance and closing the enclosure with the added height off the PCB.
I was looking at photos and trying to determine if the socketed chip stays "below" the adjacent blue 10uF capacitors and red 10nF disc capacitor, but the available photo(s) make it difficult to determine conclusively.
One interesting photo I saw was this one below. It show a socketed-chip adjacent to a 10uF cap & 10nF cap and it looks to be okay. But again, I'd need to see a side shot, and these module are much more rare to find a person who has one. I figured I'd make a unique thread about this since it can be used by people in the future, since this can be a very useful small modification. If I can't get information form here, my only alternative is to do a dry run to test-fit things. Either way, I will post my results (with photos) as a resource for others in the future.

Here is a photo of the module showing the socketed chip...
Image

My questions are:
-Has anybody added these sockets with success?
-If not, can anybody supply a sharp-angled photo of the inside of the pedal, or a side photo of the module, that shows the clearance better?

Thanks!
:)


Top
 Profile  
 
PostPosted: Sat Oct 26, 2024 10:20 am 
Offline
Moderator
User avatar

Joined: Sat Mar 04, 2006 9:15 pm
Posts: 7664
Location: Ohio
These are pix of my 27V. Not even a lo-pro socket will fit under the lid.

Attachment:
27V 001.JPG
27V 001.JPG [ 347.81 KiB | Viewed 388 times ]


Attachment:
27V 002.JPG
27V 002.JPG [ 335.06 KiB | Viewed 388 times ]


Attachment:
27V 003.JPG
27V 003.JPG [ 275.08 KiB | Viewed 388 times ]


Attachment:
27V 004.JPG
27V 004.JPG [ 320.14 KiB | Viewed 388 times ]


Top
 Profile  
 
PostPosted: Sat Oct 26, 2024 11:32 am 
Offline
User avatar

Joined: Fri Oct 11, 2024 1:32 pm
Posts: 22
Stephen wrote:
These are pix of my 27V. Not even a lo-pro socket will fit under the lid.

Attachment:
27V 001.JPG


Attachment:
27V 002.JPG


Attachment:
27V 003.JPG


Attachment:
27V 004.JPG

Thanks, these photos help a lot, especially the one with the piece of metal over the top. I will dry-fit the parts to see what's what and report back here to make a post for future reference.


Top
 Profile  
 
PostPosted: Sat Oct 26, 2024 1:13 pm 
Offline
User avatar

Joined: Fri Oct 11, 2024 1:32 pm
Posts: 22
EDIT UPDATE:

after dry-fitting everything together, I can report that you CAN indeed fit a standard socket (I didn't use a low-profile socket) on the PCB and still house it inside the enclosure given.
You can see in the photo below, the IC does extend beyond the limits of the enclosure (Photo-A), but the enclosure lid also has its own space; and you gain about half of this depth when the enclosure is secured in place (Photo-B). Also, when building, you should put the socket(s) in first, the bend the leads over, this will give you and extra millimeter or so, and the socket will lay flush with the PCB. When I was dry-fitting it, I did not bend the socket leads over, and everything still fit inside, but you can give yourself a little more room. You can see in Photo-C that the socket isn't flush with the PCB because the input/output jacks are pushing it up a little. Bending the leads will allow the socket to remain flush. Also, as the instructions say, do NOT use the inner washer on the footswitch as this will cause you to lose space.
So, between bending the socket leads, not using the inner footswitch washer, and getting that extra lid space, you can free up about 2mm +/- and this is enough space to install sockets one or both IC chips.


Attachments:
pcb.png
pcb.png [ 630.24 KiB | Viewed 379 times ]
Top
 Profile  
 
PostPosted: Thu Oct 31, 2024 3:30 pm 
Offline
User avatar

Joined: Fri Oct 11, 2024 1:32 pm
Posts: 22
UPDATE: I built it, and it closes just fine, so you CAN add a socket if you wish.

It also sounds really good, very responsive, and helps cut through. You can really tell what it does when you turn it off and realize what's missing.

It's not like it matters much, since the company is no longer doing business. oh well.

RIP-BYOC


Attachments:
20241101_111807.jpg
20241101_111807.jpg [ 53.17 KiB | Viewed 288 times ]
Top
 Profile  
 
PostPosted: Sat Nov 02, 2024 9:32 am 
Offline
Moderator
User avatar

Joined: Tue Jan 02, 2007 1:24 pm
Posts: 16305
Location: Albany, NY
Glad to hear that it worked out for you! :mrgreen:

_________________
“My favorite programming language is SOLDER” - Bob Pease (RIP)

My Website * My Musical Gear * My DIY Pedals: Pg.1 - Pg.2


Top
 Profile  
 
PostPosted: Sat Nov 02, 2024 9:56 am 
Offline
User avatar

Joined: Fri Oct 11, 2024 1:32 pm
Posts: 22
duhvoodooman wrote:
Glad to hear that it worked out for you! :mrgreen:


Yea, me too. I'm glad it sounds great, but I'm bummed-out about BYOC stopping business. Because they built "clones" of popular pedals, but also had original circuits.
Do you know of any other companies now that sell kits of both "clones" and cool original circuits? I know the Reddit DIY Pedal page has a list on the right-hand column. But BYOC used to be my main source.


Top
 Profile  
 
PostPosted: Sat Nov 02, 2024 12:12 pm 
Offline

Joined: Tue Jan 19, 2021 7:08 pm
Posts: 439
Location: Clovis, CA
Gutch220 wrote:
Yea, me too. I'm glad it sounds great, but I'm bummed-out about BYOC stopping business. Because they built "clones" of popular pedals, but also had original circuits.
Do you know of any other companies now that sell kits of both "clones" and cool original circuits? I know the Reddit DIY Pedal page has a list on the right-hand column. But BYOC used to be my main source.



You might want to look at GuitarPCB.com as Barry over there has quite a few original designs along with some cloned circuits as well.

-=SteveO

_________________
“To know, and not to do, is not to know”


Top
 Profile  
 
PostPosted: Thu Nov 07, 2024 12:27 pm 
Offline
User avatar

Joined: Fri Sep 11, 2009 9:42 pm
Posts: 5703
Location: Brewtown, USA
Madbean is an awesome resource too if you're able to source your own components.

_________________
Muad'zin wrote:
I want Pterodactyl sounds dammit, not a nice little analog sustain.


Top
 Profile  
 
PostPosted: Thu Nov 07, 2024 2:27 pm 
Offline
User avatar

Joined: Fri Oct 11, 2024 1:32 pm
Posts: 22
CaptainPeyote wrote:
Madbean is an awesome resource too if you're able to source your own components.

yes he is!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group